For a secure premise locks are necessary in order to prevent unnecessary entrance and prevent burglary. When the roller shutter has been closed by pulling it downwards, it needs to be fastened by a lock and key so that it does not run upwards again and remain open. Therefore in order to further secure the roller shutter gates and windows it is necessary to have locks on the roller shutters. Lack of locks on the shutters is like sleeping with an open window. Once the locks have been installed on the roller shuttles, security is assured. With lack of the locks, then anybody can enter into the building which should have been secured. It is proper to install two locks on large gates and windows in order to achieve a symmetrical balance. This balance fortifies the security by offering a balanced security throughout the entrance so that one cannot gain entrance through one side of the roller shutter.
How to install (mount) the roller shutter locks.
These are best mounted on the aluminum roller shutters. The following are the steps that are applied during the installation.
With the roller shutter lock on their hands, the technician marks the suitable mounting positions for the locks. He marks this on the shutter with the use of a sharp marking tool. He needs to measure this accurately in order to achieve a symmetrical balance if they are two locks. If it is one then he needs to establish the center of the roller shutter.
After the roller shutter locks have been bought, the technician should establish the size of the holes that it has from the supplier. This guides him on the size of holes that he will drill on the shutter.
He gets the desired size of drill bits from his tool kit and starts the drilling of holes on the roller shutter. The lock may be in need of two or four holes in order to hold the roller shutter lock firmly in position. The most preferable drill is the electric drill.
The technician the uses the bolts and nuts of the size of hole that has been drilled on the roller shutter to hold the roller shutter lock on the shutter. He tightens the nut against the nut until no movement can be felt. In case the hole is slightly bigger, it can be fastened by the use of washer nuts in order to achieve maximum firmness.
The locks are tested if they have been positioned as desired. The technicians should never leave the site until they have tested the locks and are satisfied that they are firmly secured.
Where to buy genuine roller shutter locks
These can be ordered directly from the manufacturers. One can also make an order directly from eBay and other trusted online shops that deal with the original products. They are then dropped at the prescribed locations. Various suppliers like Viro also have their distributors in several strategic positions in order to reach their clients quite easily. Buyers should therefore ensure that they buy the original products from the trusted dealers.
There are times when the roller shutter repairs are inevitable. The following are the instances of when roller shutters should be repaired.
Roller Shutter repairs after a burglary attempt
The first instance when the roller shutters should be repaired is when they have been damaged as a result of an attempted burglary. It may have failed or succeeded. During a break in as a result of burglary, the roller shutter may have been damaged by the use of crude weapons.
Break in as a result of lost keys
Sometimes one may damage the roller shuttle as a result of forced entry. One may need a forced entry into the premises when they have lost their keys and are not able to access the extra keys. For example if a business owner needs to operate their business yet they are not able to get the keys. The prudent thing is to gain forced entry and then call for an emergency repair.
Roller Shutter repairs as a result of wearing out
During the closing and opening of the roller shutter, it goes through high levels of friction. This wears out the joined slats with time. This is a manual process that usually should be done with care but sometimes it is not possible. Pulling the shutter from above while holding the handle can be a tedious manual process. With time the handle also becomes loose and may need to be repaired.
The rails also need servicing and repair
The rails that allow the roller shutters to run through also need frequent servicing in order to avoid repairs as a result of damages caused by frictions. The frictions are caused by the lack of grease on the rails to allow smooth movement between the rails and the shutters. The momentum that the rails experience when the shutter is being closed or opened keeps loosening the rails with time. Therefore technicians should always check on them and tighten them otherwise they will be repaired when completely worn out.
Repairing the roller shutter locks
The locks can also need repair after sometime. This can be caused by attempted burglary where the burglars may have interfered with them making them not respond to their respective keys. The locks may also have rusted if they have not been used for a very long time. This may occur when the roller shutter is permanently closed. This is a common scenario in the case of the transparent roller shutters. The repairs of these locks are usually done by locksmiths. They normally remove the locks and take to their workshop for further diagnosis and repair. It they are totally damaged, they usually recommend a total replacement of the locks with a new one.
Despite the installation of roller shuttles being a long term investment, there arises need for repairs caused by several damages. Repairs of the roller shutters and the roller shutter locks should always be done by professionals. Always contact the companies that deal with roller shuttles and are not a security threat to the asset owners.
Security is crucial for your home, business or shop. Roller shutters are the best systems you would apply to meet this goal. As the name suggests, roller shutters actually roll from top to bottom of a window or door. There are different types and meet various needs as described below;
Electric roller shutters
These shutters are operated by use of electricity. When your service provider installs them for you, they get a connection route to a source of poor, in which a switch is used. It will operate light the normal electrical bulbs where you only switch on and off. In this case, the switch will roll the shutter up to open and down to close the door or window. These systems happen to be the most expensive for the fact that it is powered by and energy which has to be paid for. You realize you will have an increment in your electrical bill at the end of the year but its results are worthwhile. First because it offers the highest security effect. You hardly involve your manual skills. The techniques used in making this system are very professional and this explains why it offers the highest degree of security. Anyone who tries to trespass the are covered with the electric roller shutters is likely to cause themselves more harm like even experiencing an electric shock. This system would be best at homes for the car garage or in the large buildings and malls especially those located in central business district areas.
Metal Roller shutters
These happen to be the most common shutters. They are a set of hard metal that rolls from top to bottom of the windows or doors of your premises. They are a bit handy in that you use your hands to roll them in the quest to closing and opening them. It seems a task but you would request your service provider to install with it a simpler means of the entire closing and opening process. The common remedy is where a strong string-like material is installed in which you pull it down to raise the roller shutters. While closing, you reverse the pull and the shutter rolls downwards. It could take time to do this but the best advantage of this is that no one in a burglary mission can break into it without the metallic noise that will draw attention to the public. For this reason it is commonly used in shops located in town areas and along highways.
Fiber glass roller shutters
These are the most expensive but have a very high degree of security. They have been in use since 1960s till date. Usually they are designed to have a wood like appearance which will work very well as a home door. They are in most cases used in garage doors due to their high ability to secure assets. They take 3-4 hours to install them which means you get to pay more as you take into account the mounting hardware and adhesives needed. However, the cost is worthwhile.
In Liverpool the security market has established the newest type of roller shutters for commercial use. These are the transparent roller shutters. These types of shutters are manufactured in such a way that the shutter is locked but can still allow the viewers to see through the shutter. This is mainly used in businesses where even under lock and key, the customer can window shop from outside the premises. In some businesses, they are left like this throughout the night while in others, the whole business walls are made of the transparent roller shutters. A small entrance is then allowed into the unit. The walls with roller shutters Liverpool are then reinforced with the use of grills. The view is spectacular while at the same time offering security of the goods. Another area where the roller shutters Liverpool are frequently used are in residential garage doors. This offers fresh air and natural light into the home garage as opposed to the dark stuffy inbuilt garages.
The Installation Technician of Roller Shutters Liverpool
The technicians who install the other types of access control should strive to have the knowledge and skill of installing the roller shutters too. This is an added advantage to them and gives them the cutting edge in the market. They become more marketable since the demand of the roller shutters Liverpool has been on the increase in the recent past. The skill is acquired in two ways. The first one is by learning the technical knowledge from a training institution while the other method is by training on the job. The best is by having experience while training on the job under the guidance of a more experienced senior technician. The manufacturers also offer frequent trainings and seminars about their product as a marketing strategy. The technician should also know how to service and repair the shutters in case of a breakdown or damage. They are usually armed with a complete tool box while on their duty, be it during installation, service or during a repair.
How to improve the security of Roller Shutters Liverpool
Always use the services of a trained, certified technician. These technicians are certified by the regulating body after going through a vigorous examination. Only the qualified are given the certificate of operation.
Always go for the shutters that have been made of strong material like aluminum and steel. These are strong metals which will not break easily and are highly burglar proof. These types of materials are also preferred to the humid atmosphere since they do not rust easily.
During installation, ensure that the rails that the shutters are to run on during opening and closing are firmly installed. They should not be loose and thus should be able to withstand the strong mechanical activity and friction during operation. The consumer should also be advised on how to apply grease on the rails to minimize friction rate.
For both the manual and electric roller shutters, one should use the correct size of padlock to secure them. They are usually robust and heavy therefore bigger padlocks are more preferred.
Your shop may be the source of you bread therefore it acts as an asset to you. The situation of having it taken down by a group of burglars is something that never comes to your mind. This means you need a very reliable security agent and the roller shutters are a solution to this. In most case you will use the metal roller shutters for the fact that they are cheap to install and maintain. They offer high security contributed to the material of its making. The metal will make noise if any attempt of breakage was done thereby drawing the attention of the security guards or passers-by.
There are a variety of security shutters that suit the market field; Aluminum shutters
These are made from aluminum and are measured to fit a variety of measurements. They are in various curtain sizes to fit the size of your door or window. They are used in large commercial centers and car garages due to their ability to offer security. They also have an aesthetic perspective in which one would paint them to their best color or design and if one wants some graphics done on it, it is equally possible. They are durable due to their finishing quality which is usually made of aluminum too thereby able to resist corrosion. This can be better achieved through painting. There are types of aluminum shutters which come as double skinned in the sense they are able to prevent the penetration of excessive light and heat in addition to their main aim of preventing burglary. Another type comes in with slats in which one vision and penetration is light through the curtain is made possible. This could also act as a good display system in which the customers can see through like if they are window shopping.
Electric shutters Electrical shutters suit the shops and are electrically operated for a reason . They happen to be the most expensive but have a very low cost of maintenance. They have a tube usually inside a barrel that helps roll the shutter up and down in opening and closing respectively. They also use a switch that will guide the rolling of the tube. Basically the manual work needed in operating them is almost insignificant. An added advantage of these shutters is that they require no added equipment like the aluminum shutters that need padlocks and springs to operate. One can also operate from inside or outside the building. With the advanced technology, the electric security shutters can be controlled using fingerprints, remote controls, external key switches, timer units among others. These techniques operate like that of the common motor wares which makes the entire situation look classy and stylish if applied for your business and shop.
In these shutters, one can brand or advertise for their business. If you have the perforated aluminum security shutters, drawing on it may be impossible but you can use color as an element of branding to market your business. If you have the fully closed shutters, a lot of drawings that signify your business van be draw to market it.